In development

Titanium hangar tools

Three small tools for the cowling and the engine bay, drawn in titanium. No metal part has been made yet.

In development. Nothing here is for sale. These are designs. There is no checkout for any of it, and the prices are what we expect to charge.

Render of the three titanium tools on a bench: the spark plug wrench, the safety-wire twister and the cowling driver.

Rendered from the 3D mockup files. Not a photograph. No metal part has been made yet.

Spark plug wrench

One flat wrench for the spark plugs and the ignition lead nuts.

The plug end is a 7/8 in six-point box. The other end is a 3/4 in twelve-point end for the ignition lead nuts, open on one side so it slips over the lead. A 3/8 in square hole in the middle takes a torque wrench. That hole sits about 3.1 in from the center of the plug end, so hold the torque wrench at a right angle to this wrench, or correct the reading for the added length as your torque wrench's instructions say. Follow the torque steps in your engine's manual.

Pockets milled into both faces take weight out and leave a stiff center web.

Plug end
7/8 in, six-point box
Other end
3/4 in, twelve-point, open on one side, for ignition lead nuts
Torque wrench
3/8 in square drive hole, about 3.1 in from the center of the plug end
Size
About 7.4 x 1.5 x 0.38 in
Torque
Use the numbers and steps in your engine's manual. None are printed here.
Material
Grade 5 titanium (Ti-6Al-4V), bead blasted, with a bronze anodized finish (design)
Weight
To be measured on the first metal part

$95 Expected price, not for sale

Cowling driver

A driver for quarter-turn cowling fasteners, designed to keep the bit off the paint.

A collar around the bit centers it on the fastener. It is meant to keep the bit from sliding off onto the cowling. The tip holds 1/4 in hex bits with a magnet.

Four spare bits ride inside the handle behind a screw cap. The grip is ridged, with flats to keep the driver from rolling off a wing.

Bits
1/4 in hex, held by a magnet
Spare bits
Four, inside the handle, behind a screw cap
Grip
Ridged, with six flats to keep it from rolling
Size
0.75 in across, 3.6 in long
Material
Grade 5 titanium (Ti-6Al-4V), bead blasted, with a bronze anodized finish (design)
Weight
To be measured on the first metal part

$85 Expected price, not for sale

Safety-wire twister

A pocket safety-wire twister with a six-sided body, so it is less likely to roll away.

The idea: clamp the two wire ends in the nose and pull. A spiral inside the body is meant to spin the nose and twist the wire. It is meant to take the place of a pair of twisting pliers in a small kit.

The jaw design is not finished. The wire range below is the target.

Body
Six-sided, 0.625 in across the flats
Length
4.85 in
Wire
Made for .020 to .041 in safety wire (target)
Material
Grade 5 titanium (Ti-6Al-4V), bead blasted, with a bronze anodized finish (design)
Weight
To be measured on the first metal part

$59 Expected price, not for sale

What is still open

  • Weights. Our own files give two sets of numbers, so we will weigh the first metal parts and print that.
  • The twister's jaws, and the exact wire range they hold.
  • Prototypes, then use on real engines and cowlings, before any of it is offered.

All three: Grade 5 titanium (Ti-6Al-4V), bead blasted, with a bronze anodized finish (design).

Before any sale: prototypes, testing, a business entity for this line and product liability insurance. See Ridgelift Supply.

Get word when Supply is ready.

One waitlist for the whole shop. News only. No payment and no deposit, and nothing in Ridgelift Supply can be ordered yet.

Free. No payment and no deposit. News only, and every email we send has an unsubscribe link. If the signup service cannot be reached, this opens a message to hello@ridgeliftaero.com for you to send. See the Privacy Policy.