Display models
Soaring Series display glider
A 1,002 mm span desk and wall sailplane with battery-powered navigation lights, from Ridgelift in Onalaska, Washington. Three offers, coming soon: print files, a printed kit, and an assembled model. None of them are for sale yet.
This is a scale display model for a desk or a wall. It is not a flying model, not a radio-control airplane, and not flight hardware. Do not install any part of it in an aircraft. The design is original; it is not a copy of a production sailplane. Renders are drawings, not photographs of a finished kit. No part has been printed as a first article yet, and the light board has not yet been fabricated. Print times come from a slicer profile. Prices are starting points and may change; not a live offer yet.

Soaring Series
Print files
The digital pack for a 1,002 mm span desk and wall display sailplane with battery-powered navigation lights. You print the 19 part designs on a desktop printer. No supports are needed.
$24coming soon

Soaring Series
Printed kit
All of the printed parts, the carbon spars and pins, the magnets, a programmed RL-GLB light board, a 1S LiPo, pre-wired LEDs, the desk stand, and the assembly guide. You put it together in about two hours.
$129coming soon

Soaring Series
Assembled and tested
Built, boxed, and the lights tested, ready to put on a desk or a shelf. The same 1,002 mm span display sailplane as the print files and the printed kit.
$249coming soon
The model
Original Ridgelift design: a slender pod-and-boom fuselage, a T-tail, and a very high aspect ratio wing with a nearly straight leading edge, a tapered trailing edge, and rounded tips. Nineteen part designs, fourteen of them in the standard kit. All of them print without supports in PLA or PETG.
- Wingspan
- 1,002 mm (39.4 in)
- Length
- 416 mm (16.4 in)
- Wing
- Root chord 56 mm, tip chord 27 mm, 4 deg dihedral, rounded tips
- Mass, ready to display
- About 364 g, including hardware and electronics
- Balance
- 161.4 mm behind the nose tip, which is where the stand socket sits
- Print, standard kit
- 485 g of filament (462 g PLA, 23 g PETG) and about 22 h 3 min
- Lights
- Red and green nav, white double-flash strobes, white tail light, red belly beacon, warm cockpit glow
- Battery
- 1S LiPo, 500 mAh, USB-C charging, about 10 to 14 hours in Display mode (estimated)
Questions and answers
Can I fly this?
No. This is a scale display model for a desk or a wall. It is not a flying model, not a radio-control airplane, and not flight hardware. Do not install any part of it in an aircraft.
When can I buy one?
Not yet. The prices on these pages are starting points and may change. These products are not in the shop checkout. Join the waitlist and we will write when they go on sale.
What is the difference between the three offers?
Print files are the digital pack you print yourself, at $24. The printed kit is the parts, spars, magnets, a programmed light board, battery, and stand, at $129, for about two hours of assembly. The assembled model is built and the lights are tested, at $249.
What printer do I need?
Every part is designed to print with no supports. The standard kit uses about 485 g of filament (462 g PLA and 23 g PETG) and takes about 22 hours 3 minutes on an H2D-class machine with 0.4 mm nozzles. The wing panels stand about 244 mm tall on the bed, and the stand base is 200 by 110 mm, so you need roughly 250 mm of build height and a bed that can take a 200 mm part. Times come from a PrusaSlicer profile that approximates a Bambu Lab H2D; your slicer may differ by 10 to 20 percent. Nothing here has been printed as a first article yet.
What do the lights do?
The RL-GLB board is a 44 by 16 mm two-layer board with a USB-C charge port, a 1S LiPo connector, a hidden belly switch, and an ATtiny402 that runs the lights. It drives red and green nav lights, white wingtip strobes, a white tail light, a red belly beacon, and a warm cockpit glow. Four modes are stored in memory: Display, Calm, Night, and Glow. A low battery stops the flashers, then shuts the board down. Firmware and the KiCad project ship with the print files.
How do I change light modes?
There is no button on the model. The belly slide switch is the only control. Switch off and on again within about 1.5 seconds to step to the next mode. The last mode is remembered.
Are the prices final?
No. They are starting prices and may change. They do not include card fees, shipping, or marketplace commissions, and the cost of goods is an estimate from late-2026 supplier list prices, not a quote.
Can I hang it from the ceiling?
A hang kit with wing clips, a ceiling plate, line adjusters, and line is coming as a $12 add-on. A vac-formed clear canopy and cockpit deck are coming at $19. Neither add-on is for sale yet.
Get word when the models go on sale.
Join the waitlist for the Soaring Series print files, printed kit, and assembled model. No payment and no deposit.