Why paper layouts fall apart
A cardboard mock-up is a great start in the hangar. It falls apart when the drawing goes to whoever is cutting. A hole that is a sixteenth too tight, a switch row that runs into a rib, or a display bezel drawn for a thicker panel than yours all cost time and material.
Raster images and PDFs make it worse. A CNC router, waterjet, or laser needs vector paths: true circles, slots, and mounting holes with sizes someone can check. Without a DXF or similar CAD file, every cutout gets re-entered by hand, and the most important part of the cockpit picks up typos.
Lay it out with real dimensions
Work in inches at full scale, with each device drawn from its installation drawing. In the Ridgelift Panel Planner you start from a template or a blank sized to your airframe, then place instruments, switches, breakers, and displays on a snap grid. Every hole is geometry, not a picture on a background.
- Size the blank: width, height, corner radius, thickness, and an arched top if your airplane has one.
- Place devices on a grid, and use the alignment helpers to keep rows straight.
- Turn on dimensions to see cutout sizes and positions from the panel edges.
- Export a DXF with cutouts and markings on separate layers, plus a layout drawing and cut list.
Group things the way you fly
Put the instruments you scan most where your eyes already are. Keep engine information together. Group switches by system, in the order you use them, and leave room for gloved fingers. Put the things you need in a hurry, like the master and fuel pump, where you can find them without looking.
Check behind the panel
Depth is where most layouts fail. Displays, radios, and connectors need room behind the panel, plus room for the harness to bend. Check each device against the structure behind it, the fuel lines, and the control runs. A layout that fits on the front can still hit a tube or a cable on the back.
Before you cut
- Confirm panel width and height against the airframe drawings and the actual fuselage.
- Leave edge margin, usually half an inch or more, for screws and structure.
- Group switches by system and leave finger room between them.
- Check the depth of every device behind the panel, especially stacked radios.
- Print the layout drawing at 1:1 and hold it up to the airplane.
- Spot-check a few hole sizes in the DXF against one maker's drawing.
Cutting it
The common stack is a 0.063 or 0.090 inch aluminum blank, a powder coat or anodized finish, and engraved or printed markings. If you cut your own, cut a test piece in scrap or plywood first. Whoever cuts it, give them the DXF and the 1:1 drawing together.
The short version, step by step
- Size the blank. Set panel width, height, corner radius, thickness, and any arched top from the airframe drawings and the actual fuselage.
- Place devices on a grid. Draw each instrument, switch, breaker, and display from its installation drawing at full scale, on a snap grid.
- Group things the way you fly. Keep engine information together, group switches by system in the order you use them, and leave room for gloved fingers.
- Check depth behind the panel. Check each device against the structure, fuel lines, control runs, and harness bend room behind the panel.
- Print 1:1 and export the DXF. Print the layout at full scale, hold it up to the airplane, then export a DXF with cutouts and markings on separate layers.
Questions and answers
What thickness should an experimental instrument panel be?
A common choice is 0.063 or 0.090 inch aluminum. Check your kit maker's drawings and the depth of the devices you plan to mount.
How much edge margin should a panel have?
Usually half an inch or more from the panel edge, for screws and structure. Your airframe drawings come first.
Why do I need a DXF instead of a PDF?
CNC routers, waterjets, and lasers cut from vector paths with real dimensions. A DXF carries true circles and slots, so nothing has to be re-entered by hand.
This guide is general information for experimental amateur-built and light-sport builders. Your kit maker's instructions and the device makers' installation manuals come first.