Buyer's guide

Drilled rock anchors and a rotary hammer

When the only flat spot is ledge, nothing screws in. A small cordless rotary hammer and removable anchors can work, where drilling is allowed at all.

Field notes coming. This guide is built from makers' published specs and listings. We have not used these products on a trip yet, so there are no test results or ratings here. Where a number appears, it is the maker's number, with the source listed at the bottom.

First, can you drill here?

Often the answer is no. In National Forest wilderness, possessing or using motorized equipment is prohibited unless authorized (36 CFR 261.18), and BLM wilderness has similar rules (43 CFR 6302). A cordless drill is motorized equipment. Outside wilderness, a drilled hole is still a permanent mark on someone's land. Ask the owner or manager, and use existing tie-downs when they are there.

The drill

A rotary hammer with an SDS-Plus chuck drills rock far faster than a hammer drill. The 12V class is light enough to carry. One published example, the Milwaukee M12 FUEL 2508-20, is 3.7 lb bare and 4.6 lb with its battery, with 0.89 ft-lb of impact energy and a 5/8 in maximum bit size. Its maker quotes up to 73 holes of 1/4 x 2 in per charge in concrete with a 4.0 Ah battery. A 12 mm by 65 mm hole removes several times as much material as one of those, so expect far fewer holes per charge, and fewer again in hard rock. That is our arithmetic, not a measured number.

Removable expansion anchors

These are climbing and rope-access anchors that lock into a drilled hole and come out by hand. One stainless 12 mm model, the Petzl Coeur Pulse, weighs 140 g, needs a 12 mm hole 65 mm deep, and is rated by its maker at more than 20 kN pull-out and 25 kN shear in 50 MPa concrete. The maker asks for a perfectly round hole and recommends a three- or four-cutter bit. Rock is not test concrete. Fractured rock, a flake or a soft layer can hold a small fraction of that, and you cannot see it from the surface.

Drilled pins

The older way is a plain steel pin, such as 1/2 in stainless rod, driven into a drilled hole at an angle away from the load, with the rope tied around it close to the rock. Cheap and simple, heavier, and dependent on the angle and the rock staying intact.

Setting one, step by step

  1. Pick the rock. Solid, not hollow when tapped, away from edges and cracks.
  2. Drill. Eye and ear protection on. Hold the drill square to the surface for an expansion anchor, or angled away from the airplane for a pin.
  3. Clean the hole. Brush and blow it out. Dust left in the hole reduces the grip.
  4. Set and tie. Set the anchor as its maker says, then tie the rope with a little slack, the same as any tie-down.
  5. Back it up. If you can, set a second anchor for each point, or add a deadman.
  6. Leave it tidy. Pull the anchors, clear the dust, and pack everything back into the caddy.

The Ridgelift bit case and pin caddy were designed for this kit, and the tie-down kit page has the full weight budget.

Sources

Specs read from these pages on November 14, 2026. Makers change specs; check the current listing before you buy. Retailer links on this site are placeholders for now. If we add paid links later, each one will be marked.

Questions and answers

Can I drill rock anchors at any remote strip?

No. Motorized equipment, including a cordless drill, is prohibited in National Forest wilderness and BLM wilderness, and a drilled hole is permanent anywhere. Ask the land owner or manager first.

How strong is a removable anchor in rock?

Nobody can say from the surface. Published ratings are for test concrete. Cracked or flaky rock can hold much less. Back it up where you can.

How many holes will one battery drill?

We do not have a measured number. The published figure for one 12V rotary hammer is 73 small holes in concrete, and a 12 mm by 65 mm hole is several times larger, so expect far fewer.